The boards should all be the same width (ex. Next, I cut four pieces of the poplar scrap board to make the bookends. I used my jig saw again to cut along this line. (Also that mark on the far right was a mistake…ignore that haha)īasically, whether you’re working with a scrap wood guitar or something else, you just need to kind of divide it how you want between the two bookends. Everything on the left will be on one bookend and everything on the right will be on the other bookend. Then I used a pencil to draw a line across the neck of the guitar where it stuck off the side of the square. I used a speed square and placed my guitar on top like shown. Now, since there is a left and right bookend, this guitar has to be divided. I then, sanded it and used a drill with a large bit to drill a hole in the middle of the guitar. Get creative □ Once I had my template, I traced it onto my cherry board and cut it out with a jig saw. You can make these bookends be anything you want them to be. On that note, this doesn’t even have to be a guitar at all. Then you can print it out and use it as a template. I like Word because it allows me to resize the image to the size I want with the rulers along the top and side of the page. If you aren’t familiar on how to do this, simply find an image shape you like and copy paste it into a Word document. (I also used it to cut a practice guitar as you see here haha) I’m terrible at free hand drawing, so I did a quick Google search and printed off a pattern to cut out and trace onto my board. If you are good at free hand drawing feel free to draw your own guitar–or any design you prefer. Step 1: Cut Out Scrap Wood Guitarįirst, I cut down a piece of my scrap cherry wood to about 11″ long. But if you like the two tone look, you could just stain whatever wood you’re using two different colors for the same effect. NOTE: I made these out of poplar for the actual bookend parts and cherry wood for the guitar. Put felt or rubber pads on the bottom corners to avoid any damage to your table or shelves.What you need to make scrap wood bookends: I went with a graduated look halfway down the cement. Under running water, wash any cement gunk off the toy. Rip the box apart in excitement like I did, or cut out one side that you can repair later with tape and use the molds again. When things are dry, remove the bookend from the cement. The wait is by far always the hardest part with cement projects - at least for me. Now wait a few days for your cement to harden. Use a tool, such as an old chop stick, to even the cement around the feet. Push the feet into the cement so that the screws go in deep, but not so much so that the feet are covered. Once you have your cement at a height you’re pleased with, it’s time to embed the toy. With every few inches of cement, I tapped the box sides so bubbles would be kept to a minimum, but honestly, I like the little gaps because it makes it look like a cross-section of the earth. I sprayed the inside of the box with Pam (this helps the cardboard not stick) and packed the cement into the box mold from the top. Next, I mixed up some cement - just follow the instructions. The toy’s plastic was soft enough for me to screw these in by hand. The toy needs to be secure in the cement, so I figured a few screws at different depths would keep things from coming loose. I then put the lid back on, and with tape, secured the side so there would be no gaps for the cement to leak in to. To make the boxes work as vertical molds, I removed the lid and cut out one side of the box. The store-bought gift boxes have a kind of protective coating that doesn’t buckle with the moisture of the cement. So, lucky me, I got to keep my prototype to keep my Bukowski collection company.įor the bookends I gave in sets as gifts, I used store-bought boxes so the shapes would all be the same. I did have some success (albeit less consistent) with chicken broth containers. I played around with using recycled materials, though most boxes that are the right size and shape are made of simple cardboard, which gives too much with the weight of the cement. I started with gift boxes from the Dollar Store, which were about four inches square, by three inches deep. Cement ( Quikrete, or even mortar mix will work).Animal toy (I find mine at the Dollar Tree and thrift stores, and have a literal suitcase full for projects).Small box (who doesn’t hoard these things?).I made a few of these dinosaur cement bookends! So, I put them together in a functional DIY. I’m not over the cement trend, and I’m certainly not over the toys-as-decor trend.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |